Facebook
TwitterJawaid_Aimviz
New Pleskian
Hi,
I have installed Plesk using following command
wget -O - http://autoinstall.plesk.com/one-click-installer | sh
And its installed successfully and shown following message on terminal :
Congratulations!
All stages of the installation/upgrade have been finished.
psa is now running on your system.
To complete the system configuration process, please proceed to URL:
https://ip-172-31-20-167.ap-southeast-1.compute.internal:8443/ or
https://172.31.20.167:8443/
Use 'root' and '<YOUR root PASSWORD>' as login name and password in case of fresh installation.
Use 'admin' and '<YOUR admin PASSWORD>' as login name and password in case of upgrade,
or if Plesk is already configured.
Further, use the following commands to start and stop the system:
/etc/init.d/psa start and
/etc/init.d/psa stop respectively.
Its not accessible from the above link which is acceptable for me because the above link contains internal network ip and my public ip is 52.74.26.140 which is not not working too. Even port 8043 is opened. I tried /etc/init.d/psa stop and then /etc/init.d/psa start but there was no difference. Below are the terminal messages :
root@ip-172-31-20-167:~# /etc/init.d/psa stop
Stopping psa... * Stopping Plesk engine pool manager sw-engine-fpm [ OK ]
done
root@ip-172-31-20-167:~# /etc/init.d/psa start
Starting psa... * Starting Plesk engine pool manager sw-engine-fpm [ OK ]
done
Starting xinetd service... done
Starting sw-cp-server service... done
Starting mysql service... done
perl: warning: Setting locale failed.
perl: warning: Please check that your locale settings:
LANGUAGE = (unset),
LC_ALL = (unset),
LC_CTYPE = "UTF-8",
LANG = "C"
are supported and installed on your system.
perl: warning: Falling back to the standard locale ("C").
Starting bind9 service... failed
Starting postgresql service... not installed
Starting spamassassin service... not installed
Plesk: Starting Mail Server... already started
Starting psa... * Starting Plesk engine pool manager sw-engine-fpm [ OK ]
done
Starting drwebd service... failed
root@ip-172-31-20-167:~# /etc/init.d/psa start
Starting psa... * Starting Plesk engine pool manager sw-engine-fpm [ OK ]
done
Starting xinetd service... done
Starting sw-cp-server service... done
Starting mysql service... done
perl: warning: Setting locale failed.
perl: warning: Please check that your locale settings:
LANGUAGE = (unset),
LC_ALL = (unset),
LC_CTYPE = "UTF-8",
LANG = "C"
are supported and installed on your system.
perl: warning: Falling back to the standard locale ("C").
Starting bind9 service... failed
Starting postgresql service... not installed
Starting spamassassin service... not installed
Plesk: Starting Mail Server... already started
Starting psa... * Starting Plesk engine pool manager sw-engine-fpm [ OK ]
done
Starting drwebd service... failed
root@ip-172-31-20-167:~# /etc/init.d/psa start
Starting psa... * Starting Plesk engine pool manager sw-engine-fpm [ OK ]
done
Starting xinetd service... done
Starting sw-cp-server service... done
Starting mysql service... done
perl: warning: Setting locale failed.
perl: warning: Please check that your locale settings:
LANGUAGE = (unset),
LC_ALL = (unset),
LC_CTYPE = "UTF-8",
LANG = "C"
are supported and installed on your system.
perl: warning: Falling back to the standard locale ("C").
Starting bind9 service... failed
Starting postgresql service... not installed
Starting spamassassin service... not installed
Plesk: Starting Mail Server... already started
Starting psa... * Starting Plesk engine pool manager sw-engine-fpm [ OK ]
done
Starting drwebd service... failed
I am not sure if these failed messages are the reason that i can not access the pleask. Could you please suggest me some solution.
Thanks
Jawaid Nawab
I have installed Plesk using following command
wget -O - http://autoinstall.plesk.com/one-click-installer | sh
And its installed successfully and shown following message on terminal :
Congratulations!
All stages of the installation/upgrade have been finished.
psa is now running on your system.
To complete the system configuration process, please proceed to URL:
https://ip-172-31-20-167.ap-southeast-1.compute.internal:8443/ or
https://172.31.20.167:8443/
Use 'root' and '<YOUR root PASSWORD>' as login name and password in case of fresh installation.
Use 'admin' and '<YOUR admin PASSWORD>' as login name and password in case of upgrade,
or if Plesk is already configured.
Further, use the following commands to start and stop the system:
/etc/init.d/psa start and
/etc/init.d/psa stop respectively.
Its not accessible from the above link which is acceptable for me because the above link contains internal network ip and my public ip is 52.74.26.140 which is not not working too. Even port 8043 is opened. I tried /etc/init.d/psa stop and then /etc/init.d/psa start but there was no difference. Below are the terminal messages :
root@ip-172-31-20-167:~# /etc/init.d/psa stop
Stopping psa... * Stopping Plesk engine pool manager sw-engine-fpm [ OK ]
done
root@ip-172-31-20-167:~# /etc/init.d/psa start
Starting psa... * Starting Plesk engine pool manager sw-engine-fpm [ OK ]
done
Starting xinetd service... done
Starting sw-cp-server service... done
Starting mysql service... done
perl: warning: Setting locale failed.
perl: warning: Please check that your locale settings:
LANGUAGE = (unset),
LC_ALL = (unset),
LC_CTYPE = "UTF-8",
LANG = "C"
are supported and installed on your system.
perl: warning: Falling back to the standard locale ("C").
Starting bind9 service... failed
Starting postgresql service... not installed
Starting spamassassin service... not installed
Plesk: Starting Mail Server... already started
Starting psa... * Starting Plesk engine pool manager sw-engine-fpm [ OK ]
done
Starting drwebd service... failed
root@ip-172-31-20-167:~# /etc/init.d/psa start
Starting psa... * Starting Plesk engine pool manager sw-engine-fpm [ OK ]
done
Starting xinetd service... done
Starting sw-cp-server service... done
Starting mysql service... done
perl: warning: Setting locale failed.
perl: warning: Please check that your locale settings:
LANGUAGE = (unset),
LC_ALL = (unset),
LC_CTYPE = "UTF-8",
LANG = "C"
are supported and installed on your system.
perl: warning: Falling back to the standard locale ("C").
Starting bind9 service... failed
Starting postgresql service... not installed
Starting spamassassin service... not installed
Plesk: Starting Mail Server... already started
Starting psa... * Starting Plesk engine pool manager sw-engine-fpm [ OK ]
done
Starting drwebd service... failed
root@ip-172-31-20-167:~# /etc/init.d/psa start
Starting psa... * Starting Plesk engine pool manager sw-engine-fpm [ OK ]
done
Starting xinetd service... done
Starting sw-cp-server service... done
Starting mysql service... done
perl: warning: Setting locale failed.
perl: warning: Please check that your locale settings:
LANGUAGE = (unset),
LC_ALL = (unset),
LC_CTYPE = "UTF-8",
LANG = "C"
are supported and installed on your system.
perl: warning: Falling back to the standard locale ("C").
Starting bind9 service... failed
Starting postgresql service... not installed
Starting spamassassin service... not installed
Plesk: Starting Mail Server... already started
Starting psa... * Starting Plesk engine pool manager sw-engine-fpm [ OK ]
done
Starting drwebd service... failed
I am not sure if these failed messages are the reason that i can not access the pleask. Could you please suggest me some solution.
Thanks
Jawaid Nawab
