Issue NGINX dont work since last update from 2017-10-31

[Haecki]

Since the update I have the problem that nginx no longer processes my ipv6 addresses.

[root@server network-scripts]# plesk sbin nginxmng -e
[2017-11-01 03:17:23] ERR [util_exec] proc_close() failed ['/usr/local/psa/admin/bin/nginx-config' '-t'] with exit code [1]
[2017-11-01 03:17:39] ERR [util_exec] proc_close() failed ['/usr/local/psa/admin/bin/nginx-config' '-t'] with exit code [1]
[2017-11-01 03:17:39] ERR [panel] Apache config (15095026210.03421100) generation failed: Template_Exception: nginx: [emerg] bind() to [ipv6ip]:443 failed (99: Cannot assign requested address)
nginx: configuration file /etc/nginx/nginx.conf test failed

file: /usr/local/psa/admin/plib/Template/Writer/Webserver/Abstract.php
line: 75
code: 0
nginx: [emerg] bind() to [ipv6ip]:443 failed (99: Cannot assign requested address)
nginx: configuration file /etc/nginx/nginx.conf test failed

 

[IgorG]

Do you have this IPv6 address listed in the output of command:

# plesk bin ipmanage -l

If not - Sync IP addresses between Plesk and OS. For that go to Tools & Settings > IP Addresses > Reread IP

 

[Haecki]

Tools & Settings > IP Addresses > Reread IP --> will not work i wait 15 minutes than 504 timeout

plesk bin ipmanage --reread will also not work

i cant also set manuell in plesk onyx !!!

 

[IgorG]

What is output of ifconfig command on your server?

 

[Haecki]

ifconfig eth0
eth0      Link encap:Ethernet  HWaddr 00:xx:xx:xx:23:92
          inet addr:82.xxx.xxx.108  Bcast:82.xxx.xxx.108  Mask:255.255.255.255
          inet6 addr: 20xx:xxx:xxx:xxx:fbd0:98ca:e283:a216/64 Scope:Global
          inet6 addr: 20xx:xxx:xxx:xxx::8b84/64 Scope:Global
          inet6 addr: 20xx:xxx:xxx:xxx:9e88:9c88:7507:2d31:601a/64 Scope:Global
          inet6 addr: 20xx:xxx:xxx:xxx:4069:1f6e:ccae:a21/64 Scope:Global
          inet6 addr: fe80::219:99ff:fea3:2392/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:43320 errors:0 dropped:0 overruns:0 frame:0
          TX packets:50771 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:8464811 (8.0 MiB)  TX bytes:32279890 (30.7 MiB)
          Interrupt:18

all my IPV6 Addresses, an ping works to the machine to this ip's

 

[IgorG]

Do you have all these IPv6 addresses listed in the output of command:

# plesk bin ipmanage -l

?

Do you have any error messages in Plesk panel.log after Tools & Settings > IP Addresses > Reread IP ?

 

[Haecki]

no, the commandline tool

plesk bin ipmanage -l
State Type IP                                  Clients Hosting PublicIP
0     S    eth0:82.xxx.xxx.108/255.255.255.255 0       79      82.xxx.xxx.108
0     S    eth0:82.xxx.xxx.70/255.255.255.255  0       1       82.xxx.xxx.70
0     S    eth0:82.xxx.xxx.101/255.255.255.255 0       1       82.xxx.xxx.101

The panel.log is clean, no entry's

 

[IgorG]

Try to enable Plesk debug mode and run

plesk bin ipmanage --reread

again. Check errors in output.

 

[Haecki]

OK, I enabled debug and executed the command
unfortunately I have to stop after 5 minutes with ctrl + c, but nothing is found in the /var/log/plesk/panel.log.

 

[IgorG]

I can only recommend creating a request to support team to do the in-depth investigation to find the reason and to fix it. Please create a ticket to support at Plesk Help Center

 

[Haecki]

OK, Thx

 

[Bitpalast]

It is possible that the IP configuration is all good, but binding to port 443 can fail, too, if the port is in use by another service, for example if httpd/apache or an additional web server on the system is using it. Check it with
# netstat -plnt | grep ':443'